One hook.
Every phase.
Reduce tripping hazards for your crew by lifting SO cords, temporary light strings, and extension cords off the floor. Easy, safe cord management through every phase of construction, from rough-in through final build-out.
Cords on the floor are a tripping hazard.
Crews drop cords as walls go up, then fight the tangle every shift: re-hanging makeshift hangers, re-routing power, working around the mess. All-T Hooks gets the cord up and keeps it there.
Tangled, underfoot, in the way.
Loose cords pile on the slab. Every pass means stepping over, snagging, and pulling slack out of the tangle.
Up, organized, out of the way.
Thread one onto all-thread, drop the cord in the cradle, move on. The floor stays clear and the run stays put.
Built to do it all.
Non-conductive, injection-molded polymer built for the jobsite. The patented cradle shape spreads the cord load so it won't crush the cord jacket, and the Safety Orange color stays visible down the run. Made in the USA.
Three thread sizes across the line — 1/2", 3/8", and 1/4" — so there's a hook for every drop.
Use a coupler to extend existing all-thread to your desired work height.
Supports cord safety through every phase of the build. Rated for suspension of cables and conduit as required by OSHA.
Cord management safety · rough-in through final build-outPick the thread, grab the hook.
Same rugged body, same 25 lb rating — sized to the all-thread already on your drop.
Injection-molded
Injection-molded
Injection-molded
Every trade, every phase.
All-T Hooks screw onto the all-thread already hanging on your job, so cord elevation takes seconds instead of a work-around. One hook per drop, from rough-in through final build-out.
Temporary power & lighting
Suspend temp power (SO) cords and temporary light strings overhead, out of the way of finishing operations.
Extension cord management
Elevate flexible extension cords along corridors and walkways so crews are not stepping over them every pass.
Trip hazard prevention
Keeps stairways, walkways, and working surfaces organized and clear. Rated for suspension of cables and conduit as required by OSHA.
Cord protection
The molded cradle spreads the load across the cord so the jacket is not crushed or pinched at the hang point.
All-thread drops
Fits 1/2", 3/8", and 1/4" all-thread. Use a coupler to extend existing all-thread to your work height.
Reusable, job to job
Injection-molded polymer in Safety Orange for visibility. Non-conductive, durable, and made in the USA.
A clean run,
drop after drop.
Made for what runs through your building.
Questions from the field.
How much weight does an All-T Hook hold?
Each hook is rated for a 25 lb maximum load with a 4:1 safety factor. The molded cradle spreads that load across the cord so the jacket is not crushed at the hang point.
What size all-thread does it fit?
All-T Hooks screw onto 1/2", 3/8", and 1/4" all-thread. Match the hook to the all-thread on your drop. Use a coupler to extend existing all-thread to your work height.
Is it non-conductive?
Yes. All-T Hooks are made from non-conductive, injection-molded polymer, and they are rated for suspension of cables and conduit as required by OSHA.
What can I hang on it?
SO cords, temporary light strings, and flexible extension cords. Anything you need to keep elevated and off the floor during construction.
When do I install them?
As soon as you strip the decks. They stay in service through ceiling close-in, so there is no swapping hangers as the job progresses.
How do I buy them?
All-T Hooks are manufactured by and distributed through Cortina Safety Products. They ship in cases of 50, same size. Contact the Cortina team to find a distributor.
Order through
Cortina Safety Products
All-T Hooks are manufactured by and distributed through Cortina Safety Products. Contact the Cortina team to find a distributor or to carry All-T Hooks as part of your product line.